Partition wall (isometric)

About 7 min read

TwIsoPartitionWall · Category: Isometric equipment

Settings

These settings are in the properties panel on the right while the widget is selected. The default value is the value the widget has when it is first added to a page.

Geometry

Setting	Type	Default	Description
Isometric axis axis	Selection	x	Isometric axis the equipment is aligned with. Switching between x and y turns the body 90° so its connections follow pipes on that axis. Options: x, y
Mirror mirror	Checkbox	Off	Mirrors the equipment along its axis; left and right sides swap, including the connections.
Wall length length	Number (1.5–16)	4	Wall length in grid units, 1.5–16. To close a corridor mouth, match the corridor width.
Door type doorType	Selection	rollUp	None: plain wall. Roll-up (hangar) and high-speed doors follow Door opening; sliding and personnel doors follow Door open. Options: none None, rollUp Roll-up (hangar), highSpeed High-speed PVC door, sliding Sliding, personnel Personnel door
Personnel door personnelDoor	Selection	none	Adds a separate personnel door next to the main door. Left/right are as seen by someone facing the wall from outside. It is not drawn if the wall is too short. Options: none None, left Left, right Right
Door label doorLabel	Text	—	Short text on the plate above the door, up to 12 characters. No plate is drawn when empty.
Floor depth behind floorBack	Number (0–30)	3	Depth of the floor strip behind the wall (corridor side), 0–30. Match the corridor length to cover the whole corridor.
Floor depth in front floorFront	Number (0–10)	1.5	Depth of the floor strip in front of the wall, 0–10.
Floor markings floorMarking	Checkbox	On	Draws yellow edge lines and a dashed walkway line along the door axis.
Panel wall color wallColor	Color	#e6eaec	Color of the sandwich panel walls.
Floor color floorColor	Color	#a9b2b7	Color of the floor strip.
Door color doorColor	Color	#8697a4	Color of the door leaf or curtain.
Door open warning color doorOpenColor	Color	#f2a33a	While the door is open, the door frame and the plate take this color.
Door control panel with stack light doorPanel	Checkbox	Off	Adds a door control panel with a three-tier stack light on top (green bottom, yellow middle, red top): at the wall end left of the door on a cold room, right of the main door on a partition wall. Each lamp binds separately in the Door panel group: Off, Steady or Blinking; tag values 0/1/2 and Boolean on/off are accepted too. On a short partition wall the side personnel door goes first, then the panel.
RFID door gate rfidGate	Selection	none	Facing: two RFID readers on both door jambs facing each other. Each reader's connection, result and fault bind separately in the Readers group; the read field shows in the doorway, each half in its reader's color. On a cold room it is hidden with a cutaway front door; on a partition wall it is added to the main door, and if the wall is too short the side personnel door and then the gate are left out. Options: none None, facing Facing (two readers)
Barcode reader at the door gateBarcode	Checkbox	Off	Adds a barcode reader next to the door, aimed at the doorway.

Operation

Setting	Type	Default	Description
Door opening (%) doorPosition	Number (0–100)	0	Opening of the roll-up or high-speed door, 0–100. Bind it to a door position sensor; any value above 0 counts as open.
Door open doorOpen	Checkbox	Off	Shows the door as open; for example, bind it to a door switch tag. Roll-up and high-speed doors use Door opening instead.
Personnel door open personnelDoorOpen	Checkbox	Off	Shows the personnel door as open; for example, bind it to a door switch tag.
Play animation play	Checkbox	On	Allows animations such as rotation, belt movement and blinking. They also pause while the browser tab is hidden or the system asks for reduced motion.
Fault fault	Checkbox	Off	Fault state, usually bound to a tag. Shows a warning badge in the fault icon color; it blinks while the animation is on.
Fault icon color faultColor	Color	#e5484d	Color of the fault warning badge.
Fault icon size (0.5–2×) faultScale	Number (0.5–2)	1	Size of the fault badge, 0.5–2×. Room for the largest badge is always reserved, so the drawing does not shift.

Readers

Setting	Type	Default	Description
RFID reader 1 connected rfidConnected	Checkbox	On	RFID reader communication state. When off the device is grey and dashed and its field is hidden.
RFID reader 1 read result rfidResult	Selection	idle	Idle, Reading, Good read, No read or Rejected (read but not allowed at this door or room). Tag values 0/1/2/3/4 are accepted in the same order. Options: idle Idle, reading Reading, good Good read, noRead No read, rejected Rejected
RFID reader 1 fault rfidFault	Checkbox	Off	RFID reader fault. Shows a red lamp and a blinking warning on the device.
RFID reader 2 connected rfid2Connected	Checkbox	On	Communication state of the second RFID reader (below the lane on a read point, right of the door on a cold room). When off the device is grey and its field is hidden.
RFID reader 2 read result rfid2Result	Selection	idle	Idle, Reading, Good read, No read or Rejected (read but not allowed at this door or room). Tag values 0/1/2/3/4 are accepted in the same order. Options: idle Idle, reading Reading, good Good read, noRead No read, rejected Rejected
RFID reader 2 fault rfid2Fault	Checkbox	Off	Fault of the second RFID reader. Shows a red lamp and a blinking warning on the device.
Barcode reader connected barcodeConnected	Checkbox	On	Barcode reader communication state. When off the device is grey and its field is hidden.
Barcode read result barcodeResult	Selection	idle	Idle, Reading, Good read, No read or Rejected (read but not allowed at this door or room). Tag values 0/1/2/3/4 are accepted in the same order. Options: idle Idle, reading Reading, good Good read, noRead No read, rejected Rejected
Barcode reader fault barcodeFault	Checkbox	Off	Barcode reader fault. Shows a red lamp and a blinking warning on the device.

Door panel

Setting	Type	Default	Description
Red lamp redState	Selection	off	State of the red lamp: Off, Steady on or Blinking. Blinking only animates while Play animation is on. Options: off Off, on Steady on, blink Blinking
Yellow lamp yellowState	Selection	off	State of the yellow lamp: Off, Steady on or Blinking. Blinking only animates while Play animation is on. Options: off Off, on Steady on, blink Blinking
Green lamp greenState	Selection	off	State of the green lamp: Off, Steady on or Blinking. Blinking only animates while Play animation is on. Options: off Off, on Steady on, blink Blinking

Other settings

Setting	Type	Default	Description
Enable Flashing enableFlashing	Checkbox	Off	Makes the widget blink (an opacity pulse every second). Usually bound to an alarm condition.
Log Button logButton	Checkbox	Off	At runtime shows a chart icon when hovering the widget; clicking it adds the Tags bound to the widget to the log Tag list.

Bindings

In the Bindings (Rules) section of the properties panel, a Tag can be bound to the following properties of this widget with a Direct binding. The binding types (Direct, IntRange, FloatRange, Boolean, Bit) are the same for all widgets; they are described on the Widget Reference page.

title, visible, authorization, x, y, width, height, rotation, class, foregroundColor, backgroundColor, borderColor, borderStyle, borderWidth, borderRadius, borderTopLeftRadius, borderTopRightRadius, enableFlashing, logButton, fillColor, fillOpacity, strokeColor, strokeOpacity, strokeWidth, strokeDashArray, hoverColor, to.type, axis, mirror, play, fault, faultColor, faultScale, length, doorType, personnelDoor, doorLabel, floorBack, floorFront, floorMarking, wallColor, floorColor, doorColor, doorOpenColor, doorPosition, doorOpen, personnelDoorOpen, doorPanel, redState, yellowState, greenState, rfidGate, gateBarcode, rfidConnected, rfidResult, rfidFault, rfid2Connected, rfid2Result, rfid2Fault, barcodeConnected, barcodeResult, barcodeFault

Common sections

While this widget is selected, the properties panel also shows these common sections: General, Layout, Appearance, Drawing, Navigation (To), Bindings (Rules). These sections are described on the Page Editor page.