Conveyor (isometric)

About 5 min read

TwIsoConveyor · Category: Isometric equipment

Settings

These settings are in the properties panel on the right while the widget is selected. The default value is the value the widget has when it is first added to a page.

Geometry

Setting	Type	Default	Description
Conveyor layout conveyorType	Selection	straight	Straight belt, or a cross / 90° transfer unit with a second belt across the main line. Options: straight Straight belt, cross Cross / 90° transfer
Conveyor length conveyorLength	Selection	standard	Standard or short frame. A short conveyor holds fewer loads. Options: standard Standard, short Short
Load type loadType	Selection	none	Type of load drawn on the belt. None shows an empty belt. Options: none None, box Box, bottle Bottle, crate Crate, pallet Empty pallet, palletCrate Crates on pallet
Crates on pallet (1–2) palletCrateCount	Number (1–2)	1	Number of crates on each pallet (1–2). Only used with load type Crates on pallet.
Isometric axis axis	Selection	x	Isometric axis the equipment is aligned with. Switching between x and y turns the body 90° so its connections follow pipes on that axis. Options: x, y
Mirror mirror	Checkbox	Off	Mirrors the equipment along its axis; left and right sides swap, including the connections.

Operation

Setting	Type	Default	Description
Load route loadRoute	Selection	main	Belt the loads travel on in a cross transfer: the main line or the cross belt. A straight conveyor always uses the main line. Options: main Main line, cross Cross / 90° transfer
Belt load (%) loadLevel	Number	50	How full the belt is, 0–100 %. The number of loads drawn follows from this value and the conveyor capacity.
Cross transfer motor state crossRunning	Selection	inherit	State of the cross transfer motor. Follow main motor copies the main motor state; Stopped and Running set it separately. Options: inherit Follow main motor, stopped Stopped, running Running
Main flow motor running running	Checkbox	Off	Operating state, usually bound to a tag. Running shows the running color or indicator and moves fans, rotors or the belt while Play animation is on.
Play animation play	Checkbox	On	Allows animations such as rotation, belt movement and blinking. They also pause while the browser tab is hidden or the system asks for reduced motion.
Visual speed (0–4) speed	Number	1	Visual animation speed, 0–4 (1 = normal). 0 stops the motion without changing the running state.
Reverse reverse	Checkbox	Off	Reverses the direction of rotation or belt travel.

Sensors

Setting	Type	Default	Description
Inlet sensor inletSensor	Checkbox	Off	Shows a photoelectric sensor at the inlet end of the belt.
Outlet sensor outletSensor	Checkbox	Off	Shows a photoelectric sensor at the outlet end of the belt.
Diagonal sensor diagonalSensor	Checkbox	Off	Shows a sensor pair diagonally across the belt.
Show inlet laser inletLaser	Checkbox	Off	Draws the laser beam of the inlet sensor, e.g. bound to a detection tag. Only shown when Inlet sensor is on.
Show outlet laser outletLaser	Checkbox	Off	Draws the laser beam of the outlet sensor, e.g. bound to a detection tag. Only shown when Outlet sensor is on.
Show diagonal laser diagonalLaser	Checkbox	Off	Draws the laser beam of the diagonal sensor, e.g. bound to a detection tag. Only shown when Diagonal sensor is on.

Status

Setting	Type	Default	Description
Show motor state color showMotorStatus	Checkbox	On	Paints the motor housing in the stopped, running or fault color. When off, the motor uses the foreground color.
Stopped motor color motorStoppedColor	Color	#37647a	Motor housing color while the motor is not running.
Running motor color motorRunningColor	Color	#2b9964	Motor housing color while the motor is running.
Faulted motor color motorFaultColor	Color	#e5484d	Motor housing color during a fault; a fault takes priority over the running state.

Fault

Setting	Type	Default	Description
Fault fault	Checkbox	Off	Fault state, usually bound to a tag. Shows a warning badge in the fault icon color; it blinks while the animation is on.
Fault icon color faultColor	Color	#e5484d	Color of the fault warning badge.
Fault icon size (0.5–2×) faultScale	Number (0.5–2)	1	Size of the fault badge, 0.5–2×. Room for the largest badge is always reserved, so the drawing does not shift.

Other settings

Setting	Type	Default	Description
Enable Flashing enableFlashing	Checkbox	Off	Makes the widget blink (an opacity pulse every second). Usually bound to an alarm condition.
Log Button logButton	Checkbox	Off	At runtime shows a chart icon when hovering the widget; clicking it adds the Tags bound to the widget to the log Tag list.

Bindings

In the Bindings (Rules) section of the properties panel, a Tag can be bound to the following properties of this widget with a Direct binding. The binding types (Direct, IntRange, FloatRange, Boolean, Bit) are the same for all widgets; they are described on the Widget Reference page.

title, visible, authorization, x, y, width, height, rotation, class, foregroundColor, backgroundColor, borderColor, borderStyle, borderWidth, borderRadius, borderTopLeftRadius, borderTopRightRadius, enableFlashing, logButton, fillColor, fillOpacity, strokeColor, strokeOpacity, strokeWidth, strokeDashArray, hoverColor, to.type, axis, mirror, play, fault, faultColor, faultScale, running, speed, reverse, showMotorStatus, motorStoppedColor, motorRunningColor, motorFaultColor, conveyorType, conveyorLength, loadRoute, loadType, loadLevel, palletCrateCount, crossRunning, inletSensor, outletSensor, diagonalSensor, inletLaser, outletLaser, diagonalLaser

Common sections

While this widget is selected, the properties panel also shows these common sections: General, Layout, Appearance, Drawing, Navigation (To), Bindings (Rules). These sections are described on the Page Editor page.