Conveyor

About 5 min read

TwConveyor · Category: Svg

Settings

These settings are in the properties panel on the right while the widget is selected, mostly in the Conveyor Settings section. The default value is the value the widget has when it is first added to a page.

Structure

Setting	Type	Default	Description
Show Legs showLegs	Checkbox	On	Draws the support legs and the floor shadow.
Roller Count rollerCount	Number	8	Number of idler rollers, 3–20 (default 8).
Show Rollers showRollers	Checkbox	On	Draws the idler rollers along the belt.

Motion

Setting	Type	Default	Description
Running running	Checkbox	On	Operating state, usually bound to a tag. Running moves the belt and load and uses Belt Running Color.
Speed speed	Number	40	Belt speed, 1–200 (default 40); higher values move faster.
Flow Direction flowDirection	Selection	forward	Forward moves the material in the drawing direction, Reverse against it. Options: forward Forward, reverse Reverse

Load

Setting	Type	Default	Description
Show Load showLoad	Checkbox	On	Shows the material or load on the belt.
Load Source loadSrc	File	—	Image URL drawn as the load instead of the material pile. Leave empty for the drawn load; not used by elevator profiles.
Side Load X Offset sideLoadXOffset	Number	0	Horizontal shift of the load in side view, −24 to 40.
Load Level loadLevel	Number	45	Length of the load as a percentage of the carrying belt, 0–100 %.
Side Load Y Offset sideLoadOffset	Number	-10	Legacy name of Side Load Y Offset; only used when that value is not set.
Side Load Y Offset sideLoadYOffset	Number	-10	Vertical shift of the load in side view, −28 to 22 (negative moves it up).

Sensors

Setting	Type	Default	Description
Show Start Sensor showStartSensor	Checkbox	On	Shows a sensor with a light beam at the feed end. The beam is brighter while running.
Show Cross Sensor showCrossSensor	Checkbox	Off	Top view only: a sensor at the crossing of the Cross layout, or in the middle of a Single belt.
Show End Sensor showEndSensor	Checkbox	On	Shows a sensor with a light beam at the discharge end. The beam is brighter while running.

Appearance

Setting	Type	Default	Description
View Mode viewMode	Selection	side	Side shows the conveyor from the side, Top from above. Options: side Side, top Top
Conveyor Type conveyorType	Selection	trough	Belt type: Flat, Trough (troughed idlers) or Cleated (belt with cleats). Options: flat Flat, trough Trough, cleated Cleated
Conveyor Profile conveyorProfile	Selection	straight	Side-view profile: Straight, Z Profile (feed, incline, discharge) or L Profile (feed, incline). The Top view always stays straight. Options: straight Straight, z Z Profile, l L Profile
Feed Length (%) feedLength	Number	30	Length of the lower horizontal feed section of an elevator, 5–70 % of the conveyor length.
Conveyor Layout conveyorLayout	Selection	single	Single draws one belt; Cross adds a second belt crossing it at 90°. Options: single Single, cross Cross
Direction direction	Selection	right	Flow direction on screen. In the Side view, Left mirrors the drawing and Up/Down show vertical arrows; the Top view is rotated. Options: right Right, down Down, left Left, up Up
Discharge Length (%) dischargeLength	Number	25	Length of the upper horizontal discharge section of a Z elevator, 5–70 % of the conveyor length.
Incline Angle (°, 0 = auto) inclineAngle	Number	0	Incline of an elevator in degrees (10–90). 0 follows the proportions of the widget box.

Colors

Setting	Type	Default	Description
Frame Color frameColor	Color	#7b8798	Color of the frame and side rails.
Belt Color beltColor	Color	#333d4a	Belt color while stopped, and while running if Belt Running Color is empty.
Roller Color rollerColor	Color	#d4dee9	Color of the idler rollers.
Arrow Color arrowColor	Color	#22c55e	Color of the direction arrows.
Sensor Beam Color sensorBeamColor	Color	#ef4444	Color of the sensor light beams.
Belt Running Color beltRunningColor	Color	—	Belt color while running. Leave empty to keep Belt Color.
Belt Accent Color beltAccentColor	Color	#65758a	Accent color of the belt surface lines.
Load Color loadColor	Color	#16a34a	Color of the drawn material or load.
Sensor Color sensorColor	Color	#f59e0b	Color of the sensor housings.

Other settings

Setting	Type	Default	Description
Enable Flashing enableFlashing	Checkbox	Off	Makes the widget blink (an opacity pulse every second). Usually bound to an alarm condition.
Log Button logButton	Checkbox	Off	At runtime shows a chart icon when hovering the widget; clicking it adds the Tags bound to the widget to the log Tag list.

Bindings

In the Bindings (Rules) section of the properties panel, a Tag can be bound to the following properties of this widget with a Direct binding. The binding types (Direct, IntRange, FloatRange, Boolean, Bit) are the same for all widgets; they are described on the Widget Reference page.

title, visible, authorization, x, y, width, height, rotation, class, foregroundColor, backgroundColor, borderColor, borderStyle, borderWidth, borderRadius, borderTopLeftRadius, borderTopRightRadius, enableFlashing, logButton, to.type, fillColor, fillOpacity, strokeColor, strokeOpacity, strokeWidth, strokeDashArray, hoverColor, viewMode, conveyorLayout, direction, conveyorType, conveyorProfile, feedLength, dischargeLength, inclineAngle, running, flowDirection, speed, showLegs, showRollers, rollerCount, showLoad, loadLevel, sideLoadOffset, sideLoadYOffset, sideLoadXOffset, showStartSensor, showEndSensor, showCrossSensor, frameColor, beltColor, beltAccentColor, rollerColor, loadColor, loadSrc, arrowColor, beltRunningColor, sensorColor, sensorBeamColor

Common sections

While this widget is selected, the properties panel also shows these common sections: General, Layout, Appearance, Drawing, Navigation (To), Bindings (Rules). These sections are described on the Page Editor page.